Dynacord IPX5:4 - The amplifiers in the IPX series are ideal for fixed installation applications, such as stadiums, arenas, concert halls, theatres, and other applications requiring high-power multi-channel amplifiers with complex speaker processing.
The integrated DSP can operate at either 48 kHz or 96 kHz, including FIR Drive. In addition to analog inputs, Dante and OCA network inputs are available via OMNEO.
Each channel can be operated individually in low impedance mode or in Direct Drive 70V/100V mode.
Technical Specifications:
- Normal Mode:
- 4 x 1300W @ 2Ω
- 4 x 1500W @ 2.7Ω
- 4 x 1250W @ 4Ω
- 4 x 1250W @ 8Ω
- Bridge Mode:
- 2 x 2600W @ 4Ω
- 2 x 2500W @ 8Ω
- Parallel Mode:
- 2 x 2500W @ 2Ω
- 2 x 3000W @ 2.7Ω
- 2 x 2500W @ 4Ω
- 2 x 1250W @ 8Ω
- Parallel-Bridged Mode:
- 5200W @ 2Ω
- 6000W @ 2.7Ω
- 5000W @ 4Ω
- 5000W @ 8Ω
- Voltage Gain:
- Low-Z Mode, ref. 1 kHz 32.0 dB, adjustable 20.0 — 44.0 dB
- Direct Drive Mode 33.2 / 36.2 / 39.2 / 42.2 dB for 70 / 100 / 140 / 200 V
- Input Sensitivity:
- Low-Z Mode, Max. Output Voltage 10.7 dBu (2.66 V), adjustable -1.3 - 22.7 dBu
- Direct Drive Mode 6 dBu (1.55 V), fixed
- THD 3 dB below maximum, AES17, 1 kHz
- DIM 100 3.15 kHz, 15 kHz
- IMD-SMPTE, 60 Hz, 7 kHz
- Crosstalk ref. 1 kHz, 12 dB below Max, 8 Ohm
- Frequency Response, ref. 1 kHz, analog input to speaker output 20 Hz to 20 kHz (±0.5 dB)
- Damping Factor, 20 Hz to 200 Hz, 8 ± >. 400
- Class D, fixed frequency
- Amplifier signal-to-noise ratio
- Analog Input A 112 dB
- Digital Input A 115 dB
- Output Noise
- Analog Input A -70 dBu
- Digital Input A < -73 dBu
- Connectivity:
- Analog audio input/Thru
- Type 2 x Euroblock with 6 pins, male
- Max. Input Level +21 dBu
- Input Impedance, balanced active 20 kOhm
- Reference Level equal to digital input +21 dBu for 0 dBFS
- Speaker output: 1 x Euroblock with 8 pins, 6 mm, female
- General:
- Nominal power consumption 700 W
- 1/8 Max output power at 4 Ohm 900 W
- Idle mode (without input signal) 75 W
- Standby mode
- Dimensions: 483 x 88.1 x 514.2 mm
- Weight: 14.3 kg
- Digital Signal Processing:
- Sampling rate 48 kHz / 96 kHz, synchronized OMNEO/Dante
- Delay/latency signal Analog input to speaker output, 48 kHz/96 kHz 0.70 ms / 0.53 ms
- Dante Network Latency typ. 1.00 ms
- Signal Processing:
- User EQ with 12 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, HiPass, Lo-Pass & Notch
- User delay 0 to 2000 ms per channel
- Array EQ 5 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, LoShelvQ, HiShelvQ, Hi-Pass, Lo-Pass and All-Pass
- Matrix delay 0 to 500 ms per channel
- Speaker EQ 10 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Hi-Pass, Lo-Pass and All-Pass
- Speaker X-Over Hi-Pass and Lo-Pass per channel dB, 6/12/18/24/30/36/42/48 dB Bessel/ Butterworth, 12/24/48 Linkwitz-Riley. Alignment delay, 0 to 20 ms per channel
- Speaker FIR Up to 1025 taps, linear phase filter, linear phase Brickwall X-Over
- Network:
- Type 2 x Neutrik EtherCON/RJ45, PRIMARY/SECONDARY redundant
- General 1000base-T/100base-TX, integrated switch
- Network audio inputs 8 channels, 48/96 kHz, OMNEO/Dante format
- Network audio outputs (monitor) 2 channels, 48/96 kHz, OMNEO/Dante format
- Network input 1 x Neutrik powerCON-HC
- GPIO Control Port:
- Type 1 x Euroblock with 8 pins, male
- Ports and operating modes 3 x GPIO, switchable Analog input/Digital input/Digital output
- Analog input range 0 V to +13 V, input resistance 40 kOhm
- Digital input limits ON:
- OFF: >. 2.0 V, Internal Pull Up (10 kOhm)
- Digital outputs ON: Switchable output to GND, max. 200 mA
- OFF: Open Collector (40 kOhm to GND)
- Reference output voltage +10 V, max. 200 mA, with short circuit protection
- User Interface:
- White/black OLED display 256 x 64
- Front panel indicators 4 x status LEDs (POWER, STANDBY, FAULT, OMNEO)
- Front panel operating elements 3 buttons (UP, ENTER, DOWN)
- Rear panel indicators 1 x status LED (STATUS)
- Rear panel operating elements: Network switch
- Power requirements 100 V to 240 V, 50 Hz to 60 Hz AC
